Page not found | Edge Products

EAS PRESSURE SENSOR 0-100 psig 1/8in NPT - 98607

Suggested retail: $151.95
Your Price: $135.95
Orders over $100 ship free. Orders placed before 2 PM MT will ship same day.



Edge's EAS Pressure Sensor is a 0 - 100 PSIg 1/8 NPT sensor that plugs directly into the Universal Sensor Input system (p/n 98605). Edge's Pressure Sensor comes equipped with the proper wires and connectors to plug right into the Universal Sensor Input system saving time and money on cutting, splicing, and crimping wire terminals to connect the sensor. Use Edge's Pressure Sensor to monitor data such as Boost PSI, Lift Pump Pressure, Air Bag Pressure, Lift Pump Pressure, Pre and Post Intercooler Pressure and many more

Tolerance: +-1.5% Full Span over temperature range of -20C to 85C and +-2.4% Full Span over temperature range of -40C to 135C.

Questions about buying this product? Our experts are available from 8 AM – 5 PM MT. Call today at 888.360.3343. Our sales team would be happy to answer any questions you have.

Terms/Conditions/Warranty Information


WARNING: Cancer and reproductive harm. Visit

BUY ANY CTS2 LINE OF PRODUCT AND GET A FREE EAS - FREE EAS PROMO - May 1st – June 30th, 2019. t’s that time of year again, Edge’s Free EGT Promo (or other EAS Device)! Are you looking for deals as summer approaches and tax refund dollars are burning a hole in your pocket? Starting May 1st through June 30th, 2019 buy any Insight CTS2*, Evolution CTS2*, Juice w/ Attitude CTS2, Revolver Kit, Stage 1 Kit with the Evolution CTS2, or a Stage 2 Kit, and you qualify for a FREE EAS product,* directly from Edge! That’s up to a $152.95 savings. Below are the approved part numbers that qualify for a free EAS product and how you can claim their EAS product.
EAS PRESSURE SENSOR 0-100 psig 1/8in NPT is rated 3.2 out of 5 by 5.
Rated 1 out of 5 by from Dry air application only Bought it to monitor fuel pressure. Received it and it says for Dry Air Application Only. This is not stated anywhere on the website. The box for it even says it can be used for fuel rail pressure and lift pump pressure, but the sensor itself says Dry Air Only. So frustrating!!! Bought the sensor and the universal input, but now I can’t use either of them! Also, the sensor is only good for 0-50 psia.
Date published: 2018-02-03
Rated 4 out of 5 by from It works good. I bought to read fuel pressure and received a sensor that was " dry air only" called and was offered a replacement, but I needed it to work sooner than I could wait. I already had one of the same sensor I was using for turbo boost. So I switched them out and it worked perfectly. Only problem I have is you have to plug up a computer every time you add or change something to make it recognize the new sensor, other than that it works great
Date published: 2017-07-03
Rated 1 out of 5 by from Eas boost sensor This thing is junk 164.00 waste of money nowhere in the description states you need to Eas adapter says plugs right into your cts so you have to spend another 152.00 for the 3 wire plug/adapter. I will never buy a edge product again almost 1000 dollars in and I'll I can read is egt
Date published: 2017-10-06
Rated 5 out of 5 by from Great addition to CTS2 Simple and easy to use. The Edge products are awesome and wish I learned about them sooner. This device allows me to monitor my fuel pressure at my regulated return. Highly recommended for modified trucks
Date published: 2018-01-19
Rated 5 out of 5 by from Great solution to for sensors! I bought this for my 2005 ram 3500 12v swapped cummins and they are just a dream to use and set up.
Date published: 2017-09-19
  • y_2019, m_5, d_24, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.12
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_5
  • loc_en_US, sid_98607, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_edgeproducts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 6.55ms

I have an Edge CTS2 Juice w/attitude. I want to monitor fuel pressure on a 2006 6.0L Ford Diesel. What parts will I need?

Asked by: Micky
You would need our Universal 5 volt and our pressure sensors. Part numbers 98605 and 98607. Those two will allow you to monitor pressure up to 100 PSIg.
Answered by: JVenz
Date published: 2019-05-07

I bought the CTS2 (TRUCK PERFORMANCE, INSIGHT CUMMINS UNLOCK) for my Ram 1500 with a 6.2 supercharged engine, i just purchased EAS pressure sensor so I can read the boost out of the supercharge, what else I need if any?

Asked by: HellRam
If you are looking to add this pressure sensor to the CTS2 you would also need the universal input part number 98605 and EAS starter cable part number 98602.
Answered by: Scott
Date published: 2018-11-19

I am wanting to monitor lift pump pressure. Will this do it and what else will I need? I have a cts2 and have the eas systemalready with an egt probe. 

Asked by: Nicholas
Yes you can use this part number 98607 but you would want to give us a call to make sure you are getting the Wet sensor that can be used with fuel. If you already have the EAS starter cable you would also need part number 98605.
Answered by: Scott
Date published: 2018-12-06

Will this work for fuel pressure setup with the cts insight screen on a 6.0 powerstroke?

Asked by: coreyk
Yes you can add our pressure sensor and use it for fuel pressure. If you wanted to add the pressure sensor you would also need to get part number 98605 and 98602 if you don't have them already.
Answered by: Scott
Date published: 2019-03-23

When I bought my edge monitor the vendor I dealt with also sold me the sensor to monitor my boost. Is there any other part that I need or will this just plug in on the truck side and the edge side?  

Asked by: Woods
Yes you would also need the universal input part number 98605 and the EAS starter cable part number 98602.
Answered by: Scott
Date published: 2018-09-24

Why do I have to buy this sensor AND a separate adapter to get this to work with my cts2? This should come with everything to hook it to your product that this is made for; just like the EGT kit does for $150

Asked by: Cj1294
The universal input part number 98605 has two inputs. They don't sell them as a kit with the sensor like the egt kit because someone might already have the 98605 and only used one of the inputs on the universal input.
Answered by: Scott
Date published: 2019-01-06

Can you get this kit with a 150psi sender to install into a compressed air tank?

Asked by: Bugsquad
Unfortunately we don't offer a 150 psi sensor but you could add our 98605 part number then add a sensor separate. If you find a 150 psi sensor that is 0-5v you could make it work you would just need to map it through our mystyle software that you can download off the website under the updates tab.
Answered by: Scott
Date published: 2018-06-22

Can this be used to monitor boost on a 2007 5.9L? If so are any other parts needed to tap into the intake elbow?

Asked by: Martin1980
Assuming you have one of our CS/CS2 or CTS/CTS2 product lines then Yes, the part number 98607 0-100 psi pressure sensor can be used for boost pressure, that plugs directly into the universal input system part number 98605, you will also need the eas starter kit cable 98602. Links below:
Answered by: Tech
Date published: 2019-04-17
  • y_2019, m_5, d_23, h_7CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.12
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_14
  • loc_en_US, sid_98607, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_edgeproducts
  • bvseo_sdk, p_sdk, 3.2.1
  • CLOUD, getContent, 7.09ms